尊龙凯时人生就是博

400-700-9998
尊龙凯时人生就是博 --官网入口Enquiry:hkmarketing@epc.com.hk 尊龙凯时人生就是博 --官网入口Whatsapp Enquiry: +85261990717
Buy
EPC Products Material Testing Equipment Fire Testing Building Product Non-Combustibility Apparatus (EN ISO 1182)
产品中心
BBS|Hot Topic
  • BBS hot topic

尊龙凯时人生就是博 --官网入口
Non-Combustibility Apparatus (EN ISO 1182)

Model:Non-Combustibility Apparatus (EN ISO 1182)

Use:Evaluates the ignitability of the product.

Standard:EN ISO 1182, IMO FTPC Part 1, ASTM E2652

Related Products

The FTT EN ISO 1182 (IMO FTPC Part 1, ASTM E2652) system has been designed with significant new features. Rather than the traditional variac control, where it is possible to supply too high a current to the heater element during the heating cycle, FTT has automated this process by using modern electronics. 

The benefits of this system over traditional variac systems, which considerably extend the life of the furnace, are:

  • Soft start
  • Ramp rate
  • Power limit
  • Over temperature device

The FTT ISO 1182 apparatus consists of the following:

Special Tube Furnace
Manufactured from steel with a polished finish. This single zone furnace has a maximum operating temperature of 900°C. The furnace is easily replaceable during maintenance and servicing procedures.

Instrumentation
A 19" instrument case houses all the instrumentation. This unit features a temperature controller, an over-temperature alarm and a power controller, which controls the furnace temperature at 750°C, compensating for supply voltage fluctuations and displaying the power (Watts) being supplied to the furnace.

Software (NonComb)
The software is a Microsoft Windows based application with simple push button actions, data entry fields, check boxes and other standard Windows operations.

The operator can monitor temperatures on a Status panel, before performing a test, without recording any data. Before a test, the specimen information (material name, density, mass, laboratory name, etc.) is entered into the computer and saved to a file.

During a test, the temperature of the furnace, specimen surface and specimen centre thermocouples are recorded at a rate of 2 Hz (i.e. every 0.5 seconds) and the temperatures displayed on a graph in real time. Also the initial, maximum and final temperatures recorded by the three thermocouples are displayed during the test run.

After the test, the user is prompted to enter any comments about the material performance, the total time of sustained flaming and the final mass. The appropriate temperature rises are calculated and then a report for the test specimen can be generated.

The test report shows the material information, the initial, maximum and final temperatures, the required temperature rises, the total flaming time, the mass loss (actual and as a percentage of the initial mass) and a graph of the recorded temperatures against time. The test report also includes a reference to the pass-fail criteria given in the appropriate Standards and states whether the specimen meets these criteria.

All the test data is saved to the hard disk as an ASCII file which can then be imported into spreadsheets for additional analysis.

Project Case
Solution
Download
网站地图网站地图
友情链接:欧洲杯比赛投注  欧洲杯竞彩国外网站  欧洲杯app排行榜前十名  欧洲杯球赛在哪里买  欧洲杯竞猜手机app  欧洲杯足球购买渠道在哪  欧洲杯买足彩app推荐  欧洲杯竞猜手机app  欧洲杯竞猜手机app  欧洲杯足球购买渠道在哪  欧洲杯足球购买渠道在哪  欧洲杯官方买球  欧洲杯下注平台  欧洲杯可以买球的  欧洲杯足球购买渠道在哪  欧洲杯买足球软件  欧洲杯外围竞猜  欧洲杯官方买球  欧洲杯竞猜网站  欧洲杯正规下单平台  
网站地图网站地图